Mateminco S03 available @nealsgadgets

veröffentlicht am 11. October 2018 in Allgemein, Coupons und Codes, EDC, flashlights, nealsgadgets von

Hello my dear friends!

Neal told me he listed the Mateminco S03 and S03 copper today!

Mateminco S03

Mateminco S03 copper

both have Quad XPG3/Nichia 219C
2100lm EDC Flashlight NarsilM V1.3

of course a code is available for members 😉
M4D M4X deals


Emitter: four LEDs, cool white (CREE) or in neutral white (Nichia), mounted on
copper DTP MCPCB
Flux: >2000 lumen
Range: 184 meters
Firmware: Tom E’s open-source GPL NarsilM v1.3 adapted by Texas_Ace

This firmware is licensed under GNU GPL V3, and can be downloaded here.

User interface: [1] By default the S43 is set to use the very intuitive Narsil smooth
RAMPING UI. Instant access to a 2.5A TURBO mode is also provided.
[2] A more conventional discrete level MODE-SET UI is available as an
alternative. Any one of 12 predefined mode-sets can be selected.
[3] MOMENTARY mode is useful for signaling purposes or rapidly/briefly
lighting up targets.

Battery: One 18350 cell (or a 18650 with the long tube). Protected cells are
recommended. Cells are not included.
Driver: Texas Avenger FET Driver with charging
Optic: quad optic
Lens: Glass with anti-reflective coating
Body: Aluminum with Type III hard-coat anodizing or stainless steel
Tripod socket: Standard tripod thread for a survival hammer
Button: Tactile with back-lit rubber boot
Ingress rating: Equivalent to IPX6, do not immerse in liquids
Impact resistance: Up to 1.5 meters
Weight: Approximately 60g without cells
Dimensions: 27 mm Ø head x 89 mm length


Default UI: Smooth ramping
This feature-rich UI provides for smooth ramping of the light output between 0 and 50%, with an easilyaccessible 100% TURBO mode.
Turn the S03 ON: single-click the button, S03 turns ON using the previously used light output level
Ramp light level: press&hold button
Reverse ramp: while ramping in one direction,release button briefly and press&hold again
Instant TURBO: double-click
Turn the Lamp OFF: single-click
MOON mode: from OFF: press the button and release as soon as the S43 turns on
Strobes: double-click for TURBO, and then double-click again.The strobes are deactivated by                       default.

To enable strobes you must klick 3 times in setting #4 (ramping) or setting #8 (modes).
(Use single-clicks to cycle forward through the differenttypes of strobes, but you have
to be quick: If resting on a strobe longer than 1.2 s it locks in and the next singleclick
is OFF. Press&hold at any time to cycle backwards through the strobes.)

Battery status: triple-click (4 blinks, a short pause, then 1 blink would
indicate 4.1 V average per cell, for example)
Electronic lock-out: four clicks to disable the S03,same to re-enable the Lamp

MOMENTARY mode: five clicks (loosen and retighten the tail-cap to return to normal operation)
Factory reset: triple-click (battery status mode), then double-click (driver temperature mode),
double-click again (firmware version mode), then press&hold for about 2 s. Four blinks confirm a successful reset

Package included:
1 x Mateminco S03 (copper) 4x XP-G3 or Nichia 219C LED Flashlight
1 x Spare 18350 body tube
1 x Spare O-ring
1 x Survival hammer
1 x Lanyard
1 x Clip

Rating: 4.0/5. From 6 votes.
Please wait...

Kommentar schreiben

Noch keine Kommentare

Pin It on Pinterest

By continuing to use the site, you agree to the use of cookies. more information

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this. Please READ and ACCEPT my Terms of Use before using my page! User of my page commit: not to post any offensive or illegal content not to link to other commercial pages not to post content without having the copyright to have respectful deal with all my active users on my side not to discuss religious or political topics not to share or post any of my deals! it is forbidden to use a program to copy any info from my blog No false information about their person or motivation persons who are working with or for manufacturers or shops (paid or not) are NOT ALLOWED to register existing members need to contact me immediately to find out if their account has to be terminated! If you use information from my pages to make money with your own afflink, you agree to pay me 1000 usd (per Code and month) as fee. Should I be disadvantaged by a user of my site, I reserve the right to legal action! Bitte LESEN und AKZEPTIEREN sie meine Nutzungsbedingungen bevor sie meine Seite nutzen! Nutzer meiner Seite verpflichten sich: keinerlei anstößige oder illegale Posts zu tätigen keine Links auf andere kommerzielle Seiten zu posten keine Inhalte zu posten deren Urheber sie nicht sind einen respektvollen Umgang mit allen auf meiner Seite aktiven Usern zu pflegen keine Diskussionen zu religiösen oder politischen Themen zu führen keine meiner Deals weiterzugeben oder zu veröffentlichen! Es ist verboten mittels eines Programms Daten zu kopieren keine falschen Angaben zu ihrer Person oder Motivation zu tätigen Personen, die für Hersteller oder Shops tätig sind (entgeltlich oder unentgeltlich) dürfen sich NICHT registireren bestehende Member müssen mich unverzüglich kontaktieren ob eine Kontolöschung nötig ist! Wer meine Informationen nutzt um sich mit seinem eigenen afflink zu bereichern muss mir 1000 Usd pro Code und Monat als Ablöse bezahlen. Sollten mir durch einen User meiner Seite Nachteile entstehen, behalte ich mir rechtliche Schritte vor! please read the FAQ if you want to know more